一．適用：

本產品適用于棉布，化纖布，滌綸,針織，腈綸，牛仔，TC高彈絲毛衣料等高彈性各種服飾布料紡織品靜電植絨工藝.

二．外觀及組成：

丙稀酸樹脂、乳白色粘稠膏狀。

三．特性：

可不用過熱，植毛效果牢固、不掉毛；手感柔軟，節約人工、電費，節能環保；無毒無異味，安全可靠。配上1008固化劑可以達到低溫固化的效果，具有耐磨，耐熱，耐水，耐洗滌等特性。（雙組份）

四．使用方法：

轉移植絨工藝
1．植絨漿加助劑的比例為2%-5%；
2．助劑和主體漿攪拌均勻后，4-6小時內須使用完，調配時請計算好用量，以免浪費漿料；
3．根據面料要求，用80-100的網版印兩遍，2-3次/遍，或絲印網版采用厚版印2-3次；
4．印好的圖案約6-8成干，再進行轉移植絨；
5．溫度：150℃-180℃，壓燙時間10-20秒，壓力約6公斤（時間和溫度可根據需求進行適當調整）；
6．正反面壓燙后，冷撕熱撕均可，洗水牢度測試請?jiān)?4小時后進行；．植毛漿加助劑的比例為2%；
7．測試水洗牢度請?jiān)?4-72小時后進行.（自然干燥時間與當天氣溫和空氣濕度有關，請確認真正完全干燥后方可進行洗水牢度測試�。�溫馨提示：
1．上述資料僅供參考，一切以客戶測試為準；
2．建議生產前請先做測試，確定后再大量使用，否則造成的后果自負.

Other detailed information

一．Substrates

This product is suitable for cotton,chemical fiber,polyester,knit,acrylon,denim,TC, high elastic silky fabric etc high elastic various cloth fabric and textile electrostatic flocking process.

二．Appearance and composition

Acrylic resin、milky white paste.

三．Characters

Free of overheating,the result of flocking is firm、do not shed, soft hand feel, cut artificial and electricity bills,energy efficiency and environmental protection,without poison, peculiar smell,safe and reliable. Compound with 1006 fixing agent can reach effect of low-temperature fixing,with characters of resistant to wear, heat ,water or wash.(two-component)

四．Usage

Transfer flock technology

1.The ratio of auxiliaries add into flock base is 2%-5%

2.After the paste and auxiliaries stir evenly,must run out within 4-6hours,on the process of mixing,should calculate the amount,avoid to waste paste.

3.According to the requirement of fabric,using 80-100mesh screen printing two times,2-3times/per time,or silk screen adopts rock table print 2-3times.

4.The pattern finished printing after drying 6-8degrees,and then make transfer flock.

5.Temperature,150-180℃,the time of press iron is 10-20seconds,the pressure is about 6KG(the time and temperature according to need to make appropriate adjustment)

6.After press iron two sides,cold tore and hot broke both OK. The test about wash fastness should be made after 24hours.(the time of natural drying is related to temperature and humidity of air,please make sure it is drying completely and make a test about wash fastness!)

Warm tips:

1.The above data is just as reference,everything stands on the customer’s tests.

2.Advising to make a test before production,after determined, in a batch production.otherwise,you should be responsible for results that caused by yourself.