一適用：

萊卡布,牛仔布(涂層布，壓光布除外)、尼龍布、TPU、PU皮革，及一些高彈性面料等.

二．性能指標：

外觀及組成：白色狀粘稠體，聚氨酯聚合物

布氏粘度：140000~160000CPS

PH值：7.0-8.0

離子類型：陰離子

固體含量：65%±1

三．特性：

立體感強，觸邊性好，高附著力，高亮光，高彈性，手感超柔軟，抗回粘性能優。表面光滑，牢度超強。耐高溫水洗、雪花洗、漂洗、酵素洗、酸洗、耐高溫蒸煮。（避免45℃以上高溫或—35℃以下低溫）優越的低溫耐折。耐黃變.常溫下保存12個月，屬于高端環保型膠漿。本產品已通過國際一線品牌（耐克，卡帕，阿迪達斯）耐折，水洗反復測試。得到了權威的認可。

PU0360立體水性墨白（機印超柔軟，似硅膠，雙組份）：立體感強，觸邊性好，高附著力，高亮光，拉伸力好，手感軟，柔軟似硅膠，干爽，耐高溫水洗，抗回粘性能優。優越的低溫耐折型，適合于機印

PU0360立體水性墨透（機印超柔軟，似硅膠，雙組份）：立體感強，觸邊性好，高附著力，高亮光，拉伸力好，手感軟，柔軟似硅膠，干爽，耐高溫水洗，抗回粘性能優，干擦4-5級，濕擦4級。優越的低溫耐折型，適合于機印

四．操作應用：

1．本產品一般使用80目120目網布，根據圖案的不同絲網一定要繃緊，這一點相當關鍵：

2．為了保證印制效果，一般不要制作太厚網版，根據厚度不同需要印5—8次，在使用厚網版印刷時印完第一次需待底層干透后再進行第二次印刷，一般印刷3—5次就能達到2-3毫米以上的高度。

3．本產品不易塞網，過稠時可加入適當水漿攪拌均勻進行稀釋。

4．在自然風干48小時后，再過溫150度8-15秒，過溫時盡量將面料過反面。

5．使用時加入1%-2%交聯劑。（加好助劑的漿料要在3~6小時內用完）

五、注意事項：

1、自然干燥時間與氣溫和空氣濕度有關。

2、調色可根據客戶需要顏色的深淺來調入色種的分量，顏色調入太多容易引起掉色現象，色種最好控制在5%之內.

3、如印容易掉色的深色布，需要測試顏色是否會升華到膠漿表面上，以減少不必要的損失。

4、使用本透明產品印花，要稍加白膠漿摻和進行調色印花有利于在紡織品面料上印花著色度飽和，更好發揮透明漿的應用效果

5、由于印花面料的多樣化，和一些外在的不確定因素做大貨之前先小樣實驗確定以后方可批量生產。未確定情況使用或操作不當引起的質量問題本公司概不負責.

Other detailed information

一．Substrates:

Lycra, denim(except coated fabric, press polishing fabric),nylon,TPU, PU leather and some high stretch fabric.

二．Performance indicators:

Appearance and composition: milky white viscous body, polyurethane polymer

Brinell viscosity:140000-160000CPS

PH Value:7.0-8.0

Ionic: anion

Solid content:65±1%

三．Features :

Super tomographic view, good side,high adhesion,glossiness and elasticity.super soft hand feel.Excellent anti after-tack,stain finish.Resistant to washing by high-temperature, snow wash,bleach,enzyme wash and acid wash. High temperature resistance steaming, yellowing resistance .The shelf life is 12months under normal temperature,belongs to high-end environmental paste.

PU0360 Stereo waterbased ink white（machine printing,super soft,just like silicone,two-component.）：High three-dimensional sense,good edge,high adhesion,high glossiness,high tensile strength,soft hand feel,just like silicone,dry,resistance to high temperature washing,excellent performance of non-after tack.Excellent low temperature folding.By the way,it is suitable for machine printing.

PU0360 stereo waterbased ink clear（machine printing,super soft,just like silicone,two-component）：High three-dimensional sense,good edge,high adhesion,high glossiness,good tensile strength,soft hand feel,just like silicone,dry,resistance to high temperature washing,excellent performance of non-after tack,the dry rub is 4-5 degree,the wet rub is 4 degree.Excellent low temperature folding.By the way,it is suitable for machine printing.

四．Operation application

1.This product usually use 80-120mesh screen, according to different patterns,the silk screen should be tightened, this one is very crucial.

2.In order to guarantee the printing effect,do not use too thick screen as usual,according to different thickness,print 5 or 8 times,when using thick screen to print,print in second time after the base dries completely in first time,as usual ,it can reach 2-3mm when printed 3-5times.

3.This product is not easy to mesh plug,when it is too thick, you could add appropriate water to stir evenly and mildly.

4.After air dry for 48 hours,and overheat at 150℃for 8-15seconds,when in the process of overheating should put the fabric in opposite side.

5.When using it,you could add 1%-2% catalyst or cross-linker.

五．Notes

1.The time of air dry is related to temperature and air humidity.

2.Adjusting color according to shade of color that customers need to add amount of pigment.If add too much it will lead to phenomenon of rubbing off, the amount of pigment should be controlled within 5%.

3.If prints on dark fabric that is easy to rub off, should be test color whether it sublimates on the surface of fabric,in order to reduce unnecessary financial losses.

4.Using clear product to print,should add white paste to adjust color printing,it makes printing looks full and reach the better application effect of clear paste.

5.Due to variety of fabric and some uncertain factors , you should make a test before in a batch production.Our company is not responsible for quality problem which caused by wrong operation or using under uncertain condition.